Location of PIXIE Analysis
The Location of the Area on each Artifact Where PIXE Analysis was Undertaken
LEVELS XII—IX
33-3-125, Awl
On a flat side, 32 mm from the pointed end
33-3-156, Awl
On a flat side at the end of the tang
35-10-101B, Pin or awl
On a flat side, at the top of the thicker end
38-13-38, Flat adze
On the metallographic section prepared from a cut taken at a corner of the non-working end
LEVEL VIII
31-52-407, Awl
On a flat side, 28 mm from the blunt end
32-21-356, Dagger/knife
On the flat side of the tang, 24 mm from its end
32-21-361, Toggle pin
On the shaft, 12 mm from the head
32-21-371, Bracelet
On a flat side, 15 mm from one end
LEVEL VII
31-52-189, Needle
On the shaft, 70 mm from the eyelet end
31-52-362, Sickle fragment
On the undecorated side, 35 mm from the rounded end
31-52-363, Bracelet
On the outer surface, 16 mm from one end
31-52-364, Bracelet
On the outer surface, 17 mm from the cut end
31-52-365, Needle
On the shaft, 25 mm from the eyelet end
31-52-366, Awl
On the flat side of the shaft, 29 mm from the head
31-52-367, Boss with a central perforation
On the convex surface, 11 mm from the edge
32-21-195, Awl
On a flat side, 14 mm from the non-working end
31-52-196, Needle
On the shaft, 26 mm from the eyelet end
32-21-198, Pin
On one side of the shaft, 21 mm from the head
32-21-199, Toggle pin
On the shaft, 30 mm below the head
32-21-200, Toggle pin
On the shaft, 39 mm from the tip
32-21-202, Toggle pin
On the shaft, 27 mm from the head
32-21-204, Pin with a rolled head
On the back of the rolled head
32-21-205; Awl
On a flat side of the shaft, 12 mm from the non-working end
32-21-206, Bracelet
On the outer surface, 28 mm from the uncut end
LEVEL VI
31-52-38, Needle
On the shaft, 54 mm from the eyelet end
31-52-47, Bracelet
On one side, 15 mm from the open end
31-52-171, Bracelet with two coils
On the outside of one coil, directly opposite the open ends
31-52-172, Bracelet
On the side, 5 mm from the open end
31-52-174, Bracelet
On one side, 25 mm from one end
31-52-175, Bracelet
On one side, 24 mm from one end
31-52-176, Bracelet
On the outside, 35 mm from one end
31-52-177, Bracelet
On one side, 10 mm from one end
31-52-180, Ring with a double spiral
On the side of the central coil
31-52-182, Flat toggle pin
On the flat side of the base of the tang, 39 mm from the pointed end
31-52-183, Flat toggle pin
On a flat side at the base of the tang, 46 mm from the pointed end
31-52-184, Flat toggle pin
On a flat side near the tang's base, 112 mm from the rolled head
31-52-185, Flat toggle pin
Near the tang's base, 38 mm from the tip
31-52-195, Needle
On the shaft, 95 mm from the tip
31-52-197, Needle
On the shaft, 47 mm from the eyelet end
31-52-202, Needle
On the shaft, 21 mm from the eyelet end
31-52-206, Toggle pin
On the shaft, 27 mm from the blunt end
31-52-207, Toggle pin
On the shaft, 41 mm from the tip
31-52-208, Pin with a rolled head
On the shaft, 40 mm from the top of the rolled head
31-52-214, Toggle pin
On the shaft, 9 mm from the blunt end
31-52-216, Toggle pin
On the shaft, 30 mm from the blunt end
31-52-217, Toggle pin
On the shaft, 15 mm from the blunt end
31-52-218, Curved blade
On a flat side, at the thicker end
31-52-225, Blade fragment
On the flat of the blade, 28 mm from the larger end
31-52-226, Blade fragment
On the flat of the blade, 6 mm from the wider end
31-52-229, Blade fragment (probably a dagger)
On the top of the mid-rib, 16 mm from the thicker end
31-52-230, Chisel
On a flat side, 70 mm from the working end
31-52-231, Blade (flat)
On the flat of the blade, 15 mm from the narrower, non-working end
31-52-233, Chisel
On one side, 18 mm from the non-working end
31-52-235, Awl
On one side, 30 mm from the broader end
31-52-238, Chisel
On one side, 25 mm from the end of the blade
31-52-239, Awl
On a flat side, 38 mm from the wider end
31-52-243, Chisel fragment
On a flat side, 32 mm from the broader end
31-52-245, Bar fragment
On a flat side, 28 mm from the rounded end
31-52-246, Pin
On the shaft, 28 mm from the tip
31-52-248, Pin
On the side of the slightly thickened head
31-52-249, Shafthole axe
On the right surface of the blade, 40 mm from the working edge
31-52-251A, Axe in a holder
On the shaft, 65 mm from the bottom of the holder
31-52-251B, Holder for an axe
On the right side, 33 mm from the collared end
31-52-259, Holdfast or handle
On the inner flat surface, 17 mm from the bottom curve of the hook
31-52-261, Holdfast or handle
On a flat side, 16 mm from the narrow foot of the clip
31-52-262, Long-handled pan
On the underside of the handle, 72 mm from the end
31-52-263, Snake with no head
On the body, 94 mm from the end of the tail
31-52-265, Snake
On the body, 79 mm from the head
31-52-266, Balance plate with four holes
On the inner surface, 5 mm from one of the holes
31-52-267, Butt
At the open end, 6 mm in from the rim
31-52-269, Boss, with a central perforation
On the underside, 4 mm from the edge
31-52-272, Irregular clump of square wire
On the flat side of the wire, 10 mm from one end
31-52-273A, Boss, with a central perforation
On the outer surface, 10 mm from the edge
31-52-274, Balance plate with four holes
On the convex surface, 5 mm from the edge
32-21-100, Sickle (folded in half)
On a flat side of the tang, 52 mm from the end
32-21-101, Sickle fragment
On a flat side of the blade, 11 mm in from the working edge
32-21-102, Sickle fragment
On the flat of the blade, 12 mm from the fragmented, broader end
32-21-106, Needle
On the shaft, 44 mm from the eyelet end
32-21-108, Needle
On the shaft, 50 mm from the eyelet end
32-21-109, Needle
On the shaft, 46 mm from the eyelet end
32-21-113, Toggle pin
On the shaft, 8 mm from the head
32-21-114, Toggle pin
On the shaft, 32 mm from the head
32-21-118, Awl
On a flat side, 33 mm from the non-working end
32-21-120, Awl
On a flat side, 20 mm from the point
32-21-121, Cosmetic kit
On a flat side, near the end of the spatula shaped tool
32-21-122, Tweezers
On a flat, outer side, 58 mm from the end of one leg
32-21-124, Ring
On the flat, outer surface of the more tightly curved end
32-21-127, Bracelet or anklet
On the side, 5 mm from one end
32-21-128, Bracelet or anklet
On the side, 45 mm from one end
32-21-129, Bracelet or anklet (in two pieces)
On the inside, 9 mm from the rounded end of the shorter piece
32-21-130, Bracelet (in two pieces)
On the outer surface of the larger piece, near the cut end
32-21-131, Spatula for a cosmetic kit
On one flat surface, 28 mm from the end with the rolled head
32-21-196, Unidentified piece
On a surface of the blade, 29 mm from the non-folded end
32-21-357, Arrowhead
On a flat side of the tang, 15 mm from its end
32-21-358, Flat adze
On the side, 38 mm from the non-working end
32-21-368, Boss with a central perforation
On the convex surface, 10 mm from an edge
32-21-369, Pin
On a flat side of the shaft, 40 mm from the bent end
33-3-90, Sickle fragment
On the flat of the blade, 36 mm from the wider end
33-3-133, Awl
At the fragmented edge of the neck
LEVEL V
31-52-30, Spearhead
On one shoulder, 8 mm from the top edge
31-52-31, Arrowhead
At the base of the tang, 22 mm from the end
31-52-32, Arrowhead
On the tang, 27 mm from the end
31-52-33, Arrowhead
On the flat central ridge, 16 mm from the tip
31-52-36, Chisel
On the side, 70 mm from the working end
31-52-37, Tweezers
On a flat side, 62 mm from the tips
31-52-40, Toggle pin
On the shaft, 10 mm from the head
31-52-44, Toggle pin
On the shaft, 45 mm from the head
31-52-45, Snake
On the body, 26 mm from the end of the tail
31-52-46, Snake
On the body, 66 mm from the top of the head
31-52-47, bracelet
On one side, 15 mm from the open end
31-52-48, Bracelet
On one side, 6 mm from the uncut open end
LEVEL IV
31-52-6, Flat adze
Near the thicker end, 10 mm in from one side, and 6 mm in from the end
32-21-20, Chisel
On a flat side, 47 mm from the working end
32-21-23, Needle
On the shaft, 54 mm from the eyelet end
32-21-24, Holdfast
On the top of the large loop formed by the wire